Back to Home Page

NewChallengerStore.com
Dodge Challenger
Interior Stainless Trim Accessories 
PART#  All Interior pieces

INSTALLATION INSTRUCTIONS

 
Included:  Packet of Promoter

VERY IMPORTANT
:  
A.  Do not remove the clear protective liner from the top of your trim piece until instructed to do so.

B.  Before you begin you must
 first prepare your dash/door surface areas where Trim pieces are going to be installed in order to allow adhesion.
You can do this by scrubbing roughly and thoroughly the entire area first with household isopropyl alcohol (found at any stores hardware department).


C.  Inspect your parts to make certain it is the right part you need.  Hold the part(s) up to where it is to be mounted to make sure it fits to your model car.

 

NOTE: If these areas have been treated with Armor-all or any such surface protector, installation will NOT work unless these treatments have first been COMPLETELY removed using special chemicals. 
 

PLEASE NOTE: We ask that you please follow instructions carefully - parts can not be returned if scratched or if the rear red liner has been removed (even if re-attached). 

1.  Thoroughly clear the area where you are going to stick your part to.  Use rubbing alcohol and Isopropyl alcohol solution.

2.  You have been provided with a tape test strip.  Use this to test the tack by peeling off the back of a test tape strip and seeing if it sticks to the area you cleaned.  If it sticks well then you can proceed with your installation. 
If it does not stick well then scrub interior area with a rough surface pad.  Continue to clean until the test tape sticks well.  You can use some masking tape to test the surface as well.

3.  You have been provided with a tape test strip.  Use this to test the tack by peeling off the back of a test tape strip and seeing if it sticks to the area you cleaned.  If it sticks well then you can proceed with your installation. 
If it does not stick well then scrub interior area with a rough surface pad.  Continue to clean until the test tape sticks well.

4.  Once your areas have been prepared use the adhesive promoter packet or pen (provided) to wipe the areas of your interior where you will be attaching your new stainless trim pieces.  This clear liquid is odorless and will not stain or damage your paint or your interior panels.  Allow a few seconds to dry.

5.  Once the interior surface area is ready test the placement and fit of your trim piece before you take the red backing off.  Hold the trim piece up to the area it is to be mounted to.  Move it around until you are satisfied with the exact position it is to be mounted to.  (The entire back of the trim piece must have solid contact with the interior surface, including trim pieces with a bend or curve to them).  This may require to slight bend the piece with your hands.

6.  Once you are ready remove the rear red backing off the trim piece.  Hold it just over the area it is to be mounted on.  Slowing lower it into position and very lightly set it on the interior surface.  Make any slight last minute adjustments in position.  Now press it down firmly all over the surface of the trim piece.
You may now remove the top clear protective liner.

Reminder:  Before you remove the liner for permanent attachment place each piece into position and check the fit and also get acquainted with just how each part sets in place. It will be necessary to form a few of the parts by hand to CONFORM to the shape of your dash to insure a nice perfect fit without forcing the shape. Once you are satisfied with the shape and fit peel the red release liner and firmly press each piece into position.

Maintenance note: Extra care must be taken when cleaning your dash kit. It is a good idea to lightly dust your kit with a clean soft cloth first in order to prevent any particles from scratching it. Then wipe (using a new clean soft cloth) with a good quality streak free glass cleaner.

For Help - please call 352 688 8160 M-F or email us at admin@NewChallengerStore.com

NewChallengerStore.com a HotCarAccessories.com website

 Copyright 2005 - 2017
Not affiliated with Dodge, Chrysler Corporation or it's divisions.